Imperial Impex

Being a well-distinguished company in the market, we are into offering Fosroc Brushbond Waterproofing Chemical.

Sika Top seal 551 Earlier branded as MASTERSEAL 551 EL is an elastomeric flexible, two component polymers modified cementitious system that requires only on site mixing forming ideal waterproof coating on concrete, masonry, and most other construction materials. When cured, a 2mm thick MASTERSEAL 551 EL membrane shall accommodate movements up to 0.5mm, or up to 1.2mm when reinforced with 100% virgin polypropylene woven fabric.  Uses Water-retaining structures subjected to movements  Basement-waterproofing To protect concrete from water, carbonation and de-icing salts. Waterproofing of roofs, sunken floors in bathrooms, WC, etc. Waterproofing coating for drinking water tanks, sumps, etc. Advantages Retains flexible when submerged Good chemical resistance against soft water, domestic waste water, manure or other liquids moderately aggressive to mineral substrates.  CO2 Resist to occasional foot traffic  Water vapour permeable  barrier, provides anticarbonation benefits Excellent adhesion.  Bonds to porous and non porous surfaces. Non toxic-suitable for contact with potable water. Saves time - Can be applied to 24 hour-old concrete

Asian Paints SmartCare Waterproofing Membrane is a APP modified polyester sheet reinforced bituminous membrane for superior waterproofing. This membrane exhibits excellent tensile strength, tear strength, puncture resistance and dimensional stability.

Dr. Fixit Prebond membrane is a preformed HDPE fully bonded membrane that bonds to the wet concrete cast on the membrane. After the membrane bonds with the concrete it forms an integral seal which prevents lateral water migration and makes it unaffected by any substrate settlement below the slabs. Reinforcement can be directly laid on top of the membrane and it does not require screed protection. Dr. Fixit Prebond is a unique HDPE membrane comprising of a virgin HDPE layer and a pressure sensitive adhesive layer which is covered by a weather proof protective layer. The adhesive layer is activated when the concrete is poured on the membrane and it enables the membrane bond to underside of the concrete which prevents the ingress of water into the structure as well as prevents tracking of water between the membrane and the structure and provide a positive side protection against ingress of sub soil water. Dr. Fixit Prebond can be used for horizontal as well as vertical blind side application.

SikaTop-107 Seal Plus IN High performance acrylic polymer modified cementitious waterproofing coating DESCRIPTION SikaTop-107 Seal Plus IN is a flexible, two part, high performance acrylic polymer modified cementitious liquid applied waterproofing coating system. It comprises of a liquid polymer and a cement based mix incorporating special admixtures. It is applied to concrete and mortar to prevent water infiltration with flexibility. It is available in a user friendly pre-packed kit form. It is suitable for waterproofing of drinking water tanks USES Waterproofing applications for various structures such as: Potable water holding tanks like reservoirs,overhead water tanks ,etc (CFTRI Certified)  Raw water concrete tanks, reservoirs, waste water tanks  Terraces, balconies, sunshades, etc.  Flat and small roofs  Basement and retaining walls  Swimming pools, fountains, water bodies, canals  RCC gutters, drains and planter boxes  Wet areas like toilets, kitchen, utility, sunk slabs  Lift pits, sump, etc.

Sikalastic-562 IN is a water based ,one component cold applied liquid Polyurethane waterproofing membrane that can be applied directly from the container. It provides a seamless, smooth waterproof finish with excellent UV resistance ,excellent crackbridging properties and great aesthetics.It also shows remarkable resistance to ponded/accumulated water and does not get washed away easiliy. It is suitable for both exposed and covered roofing applications . USES   Podiums & Planter areas (Concealed )  New construction and refurbishment projects  Waterproofing of external walls  Waterproofing and renovation of old roof tiles   The product can be used on the following substrates: Concrete and cementitious substrates Flat and sloping fully exposed or covered roof structures Roofs with numerous details such as penetrations, drains, roof lights and complex geometry  Brick  Metal  Clay tiles  Unglazed ceramic tiles  Bitumen sheet membranes  Bituminous coatings

SikaLatex Power High performance SBR based multipurpose polymer for waterproofing, repair and bonding
DESCRIPTION SikaLatex Power is a latex-based, water-resistant multipurpose admixture for use in areas subject to humidity, dampness and continuous water contact. When added to cement mixtures, it improves water resistance and bonding strength by forming a reinforcing polymer that increases long term durability and flexibility of the mix. It is fully soluble in water and is to be added directly to the gauging water of mortar, concrete or cementitious grout. USES SikaLatex Power is used as bonding agent, waterproof coating and site-mix mortar admixture for the following applications: Bonding of rendering and coating layers  Bonding between successive concrete casts  Cement grouting and screeds  Polymer modified repair mortars  Masonry mortars  Renders  Tile fixing and panelling  Waterproof plastering

600 PF constructive solutions Pitch Free PU based Liquid applied single component elastomeric waterproofing membrane.

Brushbond UltraFlex
page 1 of 2
High Performance & Ultra fl exible polymer
modifi ed elastomeric waterproofi ng membrane
system for concrete and masonry surfaces.
Uses
Brushbond UltraFlex, when fully cured, provides a seamless
Elastomeric waterproof membrane for use in roof areas, wet
areas, bathroom, water tanks, swimming pools, reservoirs, pre-
cast joints where a tough elastomeric water tight membrane
is required
Advantages
 Low VOC.
Can be applied to damp substrates.
No primer required.
Elastomeric - able to bridge cracks
Able to take foot traffi c when cured.
Factory pre-blended two component system ensure quality
control at site control.
Description
Brushbond UltraFlex is a two component polymer modifi ed
waterproof membrane which is supplied in readymix kits.
When mixed, an easily brushable coating is produced. It can
simply be applied by a stiff brush, roller, or trowel to obtain the
desired thickness.
Brushbond UltraFlex consists of specially selected cements,
graded hard wearing aggregates and additives supplied in
powder form together with a liquid component of polymers
providing exceptional adhesion, resiliency, fl exibility, toughness
and durability.
Standards compliance
Brushbond UltraFlex conforms to the requirements of:
DIN 1048, Part 5, 1991
ISO 7783:2018
ASTM D412 : 2013
Brushbond UltraFlex is deemed to be suitable for use
with potable water sources as tested as per USFDA
CFR 175-300

Asian paints Smartcare Damp Proof Paint is a water proofing coating

Backed by rich industrial experience we are offering concrete admixture to our customers providing the best services to our customers at reasonable rates

DESCRIPTION Sika MonoTop-108 Water Plug IN is a ready to use, rapid-setting, waterproof cement mortar for stopping water leaks in concrete and masonry. USES      To instantly seal negative water pressure leaks through cracks, gravel pockets and casting joints To instantly seal water leakage during waterproofing of water tanks, basements and sunken pits etc. Instant sealing of water drainage outlets during waterproofing treatments Instant sealing of leakages in concrete/masonry structures As plugging mortar for fixing nozzle / grouting ports during injection grouting

Nitocote CM210 provides a cementitious, elastomeric  waterproof coating with inherent crack-bridging ability. Typical applications include:   Potable water retaining structures.   Swimming Pools.   Internal basement waterproofing.   Drainage culverts.   Wet areas: Kitchens, bathrooms, shower rooms   Foundations in contact with ground water under saline         conditions.    Vapour barrier.   Damp proofing for facades. Advantages   Withstands high positive and negative hydrostatic pressures   Excellent crack accommodation before and after immersion   Approved for use in contact with potable water   Excellent bond to concrete and masonry   Long working life   Easy application by brush, trowel or spray   to green or damp concrete

High build fi bre Reinforced Acrylic Elastomeric Waterproofi ng render for roofing Uses Brushbond Roofguard is high build fi bre reinforced seamless waterproofi ng render suitable for waterproofi ng of old & new roofs, it is a polymer base product applied in three OR more coats & each coat with different colours for monitoring correct thickness. The product can be applied directly on existing concrete, brickbat coba, and screed concrete even without removal provided the substrates are sound enough for application of the coating avoiding the risk of damage to the old roof associated while removing of the existing overlays. The product provides a seamless, tough durable water resistant coating which can withstand light pedestrian traffi  c and also has excellent weather resistance for exterior applicatio

Dr. Fixit Pidiproof LW+ is specially formulated integral liquid waterproofing compound composed of surface active plasticising agents, polymers & additives. It is used as an additive for cement concrete, mortar & plasters.  It makes concrete cohesive and prevents segregation.

Dr. Fixit Pidicrete URP is based on modified styrene butadiene latex supplied as a ready to use bonding agent in liquid consistency. It is used for repair of spalled concrete – floors, columns, beams, chhajas, slabs & waterproofing of toilets & bathrooms, small terraces etc. as it bonds strongly to old & new concrete and to plasters. It reduces shrinkage, prevents cracking, dust pick up & improves abrasion resistance.

Dr. Fixit Fast Flex is a high elastic, waterproofing cement based material. With special waterproofing properties, easy to use by plastering, applying by using a brush and roller or trowel. Can be painted or overlaid. Use with waterproofing for non-toxic water tanks, can be used with drinking water. (Passed the water quality test on toxic substances (heavy metals) of the Water Quality Control Department) Provincial Waterworks Authority. After mixing the two parts together, the liquid material can be applied on the desired surface. After drying, it looks like a rubber sheet. It has the property to prevent water seeping through, seamless and flexible, not cracking. Japanese standard  Dr. Fixit Fastflex is a 2-component cement-based waterproofing material, which is powdered (fine sand, sizing), liquid (modified acrylic polymer) and nontoxic substances, environmentally friendly - free Volatile Organic Compound (VOC), excellent waterproofing property - no leakage up to 10 m. hydrostatic pressure  Area of Application   Concrete foundations, basements wall and lift pits.   Swimming pools, water tanks and reservoirs.   Concealed roofs, parking decks, bathroom, toilet, kitchen, balconies and planters.   Any other concrete, cement or masonry surface subject to damage from moisture.

Dr. Fixit Pidifin 2K is 2 parts polymer-modified flexible cementitious waterproofing membrane coating specially formulated for Concrete and Masonry Surface which is supplied in ready-mix kits (2 parts). When the dry part is mixed with acrylic-modified emulsion and applied according to direction, the cured.  Dr. Fixit Pidifin 2K will become a tough, flexible and seamless waterproof membrane and acts as an excellent water barrier to Concrete and Masonry Surface.

Lokfix mix and place grouts are used for high strength corrosion resistant anchoring of bolts and bars from 12-51 mm diameter into concrete, rock, masonry or brickwork where high speed of installation and early application of load is required.  Permanent installation of reinforcement starter bars, foundation bolts, base plates, balustrading, barriers and safety fences, railway tracks, tie-back anchors, reinforcement dowelling abutments, ground anchors for towers, cranes, dock sills etc. 
Advantages  
Rapid strength gain.   Vibration resistant.   Corrosion resistant.   Non-expansive.   Can be placed underwater.  Standard compliance  Product is tested in accordance with BS6319 and BS5080.  Description  Lokfix is produced in two versions.  The two versions of Lokfix are all pre-measured, two part, filled polyester resin grouts.  After hardening, the grout produces anchorages of consistent reproducible values. 
The versions are: 
Lokfix S - used where hole diameter is less than 25 mm greater than the bar diameter.
  Lokfix P - used in overhead or horizontal holes where bar/hole relationship conforms to Lokfix S.  The thixotropic nature of Lokfix P reduces flow of grout out of the hole.  Technical support  Fosroc offers a comprehensive range of high performance, high quality, and construction products.  Fosroc offers a technical support package to specifiers and contractors as well as technical assistance in locations all over the world.

Dr. Fixit Roofseal Classic New is a single-component, elastomeric waterproof coating designed for roofs for top coat application. It combines waterproofing and heat insulation in one application, utilizing Acrylate PU hybrid emulsion technology and reinforced with nanofibers for superior performance.  Standard Compliance / Specification Meets ASTM D6083 - Type II standard specification Areas of Application Existing flat or sloped roof surfaces such as: } Brickbat coba finishes } Cement mortar screeds } China mosaic tiles } Clay Tiles } Ceramic Tiles. Features & Benefits } Protection: Provides exceptional waterproofing and reduces surface temperature by up to 10C in peak summer. } Flexible & Crack Bridging: The highly flexible formula bridges crack up to 2 mm, of fering long -lasting protection. } Durable Coating: Perfect for roofs with light foot traffic. } Easy Application: Single-component, self -priming, ready-to-use waterproof coating. } Eco-Friendly Choice: Non-toxic and VOC-compliant water-based coating for a sustainable solution. } Warranty: 10 years waterproofing.

LDr. Fixit Primeseal is water-based primer composed of acrylic emulsion polymer, properly selected fine fillers, white pigments & additives in water as a medium. It is used as primer over exterior & interior building walls before application of Dr. Fixit Raincoat & other water based paints.

Dr. Fixit Pidicrete URP is based on modified styrene butadiene latex supplied as a ready to use bonding agent in liquid consistency. It is used for repair of spalled concrete – floors, columns, beams, chhajas, slabs & waterproofing of toilets & bathrooms, small terraces etc. as it bonds strongly to old & new concrete and to plasters. It reduces shrinkage, prevents cracking, dust pick up & improves abrasion resistance.

Asian Paints SmartCare Hybrid PU Sealant is a single component, moisture curing, low modulus silyl-terminated polyurethane sealant for sealing of dynamic joints.

Asian Paints SmartCare Tile Grout - Epoxy Based is a two component epoxy resin based tintable grout specifically designed for use in application of ceramic tiles, vitrified tiles and stone joints where a hygienic and sterile condition is expected.

HIGH PERFORMANCE SOLAR REFLECTIVE WATERPROOF COATING FOR ROOF
Description
Dr. Fixit Roofseal Select is formulated with Acrylate-Silicon-Based Technology and, upon curing, provides outstanding waterproofing capabilities. Dr. Fixit Roofseal Select liquid membranes are highly flexible, accommodating roof movements caused by temperature variations and resisting crack formation. When applied in compliance with the guidelines for application, this will extend the life of the roof by several years without the need to replace the entire roof structure. Additionally, white-colored membranes also offer a cool roof effect by reflecting solar radiation, especially during the harsh summer months.

Sikalastic-510 CoolCoat IN is a 1-part, acrylic, water based, elastic, cold applied liquid membrane that can be applied directly from the container. It provides a seamless, smooth waterproof finish which is resistant to UV exposure, environmental pollution and has elastic and vapour permeable properties.

Asian Paints SmartCare PU Magnum US is single component waterproofing liquid membrane, offering superior mechanical and chemical properties, as the same is based on pure, elastomeric, polyurethane resin. This product is designed to be applied over concrete surfaces which must be laid over by a protective cement screed.

SikaLatex SBR Superior performance SBR based multipurpose polymer for waterproofing, repair and bonding DESCRIPTION SikaLatex SBR is a superior modified styrene butadiene emulsion to be mixed with cement slurry, cement mortar, concrete or cementitious grout for improved adhesion and water resistance properties. It is fully soluble in water and is added directly to the gauging water of slurry, mortar, concrete or grout. USES SikaLatex SBR is used as bonding agent, waterproof coating and site-mix mortar admixture for the following applications: Bonding of rendering and coating layers  Bonding between successive concrete casts  Cement grouting and screeds  Polymer modified repair mortars  Masonry mortars  Renders  Tile fixing and panelling  Waterproof plastering

Asian Paints Epoxy Tri Block is an epoxy cementitious coating for positive side waterproofing of cementitious water retaining structures.

modifying and improving  bonding  of floor toppings, renderings and mortars; repair of worn, damaged and spalled concrete, repair of large cracks; polymer modified floor screeds; waterproof plasters for masonary  and slurries. Advantages Simple to use - Single component,  gauged as  required. High - Provides excellent bond to  concrete,  adhesion plaster,  masonry, stone work, etc. Improves -Gives weather resistant mortar with improved durability impermeability to chlorides and other harmful agents. Reduces - Provides waterproof screeds, plasters  and Permeability slurries. Increases - Improved tensile and flexural properties strength allow thin applications. Versatile - Compatible with all common hydraulic cements. Cost effective - Nitobond SBR (Latex)  is economical  to use Description Nitobond SBR(Latex)  is modified styrene butadiene emulsion specially designed for use as a bonding aid and gauging liquid for cementitious systems.  It is resistant to hydrolysis and can therefore be used for external applications too. Technical Support Fosroc provides a technical advisory service supported by a team of specialists in the field.

Dr. Fixit Raincoat Waterproof Coating is composed of high quality emulsion polymer, weather durable pigments, properly selected & graded fine fillers, additives & biocides. It is used as a waterproofing & protective coating for exterior walls of the buildings.

Asian Paints SmartCare Vitalia NEO is an integral liquid waterproong compound with advanced formulation and superior plasticizing additives for cement concrete, mortar and plasters. The product is formulated with selected surface active plasticizing agents, chemicals & additives which make the cement concrete/ plaster mix cohesive and upon curing, reduces water permeability.

Dr. Fixit HydroShield PUD Plus is ready-to-use liquid applied Elastomeric roof coating based on a hybrid polyurethane technology for large Roof & Terraces without needing to break it. Offering great durability in ponding water (compared to common acrylic coatings), excellent resistance under sun exposure and waterproofing under difficult weather conditions and temperatures for many years.

POLYURETHANE COATING FOR WATERPROOFING AND PROTECTION OF WATER TANKS Description Dr. Fixit TankPro W is a two-component, solvent-free, thixotropic coating, based on high quality elastomeric polyurethane resins. After polymerization, it produces a strong, elastic, hydrophobic membrane suitable for waterproofing and protection of water tanks. Areas of Application Waterproofing and protection of: o Water tanks made of reinforced cement concrete (RCC). o Prefabricated concrete tanks, Drinking Water Tanks and other waterbodies. Features and Benefits o Excellent adhesion on RCC surface. o Being solvent-less, it can easily be applied in closed spaces. o Extremely hydrophobic and hydrolysis resistant. o Certified for potable water tanks, in accordance with the US FDA 175.300 requirements. o Single coating for Waterproofing and Protection for water tanks giving faster turaround time.

Dr. Fixit TankPro E CHEMICAL RESISTANT COATING FOR WATERPROOFING AND PROTECTION OF CONCRETE STRUCTURES Description Dr. Fixit TankPro Eis a two-component, solvent-free advance polymer coating. It produces a strong liquid applied membrane of sufficient elasticity with outstanding adhesion to various types of surfaces. It is specially designed based on pure hydrophobic polymer resin which results in excellent abrasion resistance and protect the concrete against aggressive chemicals. Areas of Application Waterproofing and protection of: o Sewerage tanks, aeration tanks, sedimentation tanks etc. o Wastewater treatment plants. Features and Benefits o Easy to apply, can be applied using Trowel. o Excellent adhesion to a variety of substrates and building materials. o Being solvent-less, it can easily be applied in confined spaces. o High chemical & abrasive resistance as per ASTM D543 & ASTM D4060.

SikaTop-107 Seal IN is a two part, acrylic polymer
modified cementitious liquid applied waterproofing
coating system. It comprises of a liquid polymer and a
cement based mix incorporating special admixtures. It
is applied to concrete and mortar to prevent water in-
filtration.
USES
Waterproofing applications for various structures
such as:
Potable concrete water tanks, reservoirs, waste water
tanks

Terraces, balconies, sunshades, etc.
Flat and small roofs
Basement and Retaining walls
Swimming pools, fountains, water bodies, canals
RCC gutters, drains and planter boxes
Wet areas like toilets, kitchen, utility, sunk slabs
Lift pits, sump, etc.

Interior and exterior waterproofing and damp-proof-
ing of concrete, cementitious rendering, brickwork
and blockwork

Protection of concrete structures against the effects
of de-icing salts and freeze-thaw attack

Pore / blowhole filling
Sealing fine “hairline” cracks in concrete structures
not subject to movement

Sealing internal basement walls against dampness

Liquid integral  waterproofing admixture for all types of concrete and mortar. USES SikaCim is recommended for use in structural concrete, particularly for the following Slope Roof Slabs  Flat Roof Slabs  Beams  Columns  Slabs  Excellent for internal and external plaster of buildings etc.  Repair and renovation

PTION Sikagard-67 is a water based, solvent free, odourless, epoxy resin protective coating. USES Sikagard-67 may only be used by experienced professionals.   Applied on concrete, rendering, stone, asbestos and cement. Protective coating against weathering and mild chemical attack in areas such as cantilevers, galleries, retaining walls, basements, workshops, reservoirs and balconies. CHARACTERISTICS / ADVANTAGES  Protect cementitious structures against weathering  Resistant to oil and grease  Weather-proof  Mild dew-resistant  Solvent free  Suitable for portable water reservoirs   Easy to apply   Adheres to damp surfaces  Odourless

Enriched by our vast industrial experience in this business, we are involved in offering an enormous quality range of Dr Fixit 603 Newcoat Waterproof Coating.